CALL TO ORDER
(800) 882-7004

Commercial Applications

Metal Applications Fence
Metal Applications Driveway

Commercial Use: Metallic Coatings

Long-life metallic coatings without the limitations

Our metallic coatings can be field-applied on standing seam metal roofs, mansards, or walls, and on various substrates such as wood, metal, masonry, mineral surface roofing, granular and clay emulsion surfaces and on composition shingles. In factory production, it can be applied to metal substrates of aluminum or galvanized metal.

Our metallic coating is a liquid, specifically formulated with acrylic resins and pure ground copper, which cures to form an elastomeric membrane. Our popular Copper Metallic Coating provides a long-life copper finish without the limitations, expense or maintenance problems of copper sheets. 

Coverage on smooth surfaces is approximately 200 sq. ft. per gallon 3 mil film. Two coats are required with a cross hatch application. Products should not be applied in freezing conditions. If our patina solution is to be applied, the first coat of metallic coating should be cured. The application of the patina should be applied to the second coat just before it dries. This is dependent on temperature and humidity. Apply a mist of the antique solution at a rate of 250 to 350 sq. ft. per gallon.

Our customers are builders, contractors, sign makers, metals fabricators, architects, interior designers, and artists.

I know a good coating when I use one - pure powdered metal in a very high quality clear acrylic coating. I have used the product exclusively for exterior surfaces in the So Cal desert. The product is extremely durable. We painted the bell tower at my golf club 40 years ago, it looks the same as the day we painted it.

Available Commercial Metallic Coatings

Sample Metal Copper

Copper

Sample Metal Bronze

Bronze

Sample Metal Iron

Iron

Sample Metal Pewter

Pewter

Sample Metal Brass

Brass

Commercial Use: Patina Finishes

Achieve high-end results for a fraction of the cost

Metallics and Patinas, LLC is your source for green, brown, or blue patina finishes. Somewhat similar to paint, but truly not a paint, our water based patina coatings can be applied to many different surfaces using an garden or commercial plastic Hudson sprayer, a roller, or brush.

Our patina solutions are used with our metallic coatings extensively on exterior signage, wrought iron railings and gates, yard art, and fountains. Also used on hardy backer and concrete both interior and exterior.

Our customers are builders, contractors, sign makers, metals fabricators, architects, interior designers, and artists.

PATINA Application

The most common method of applying the Patina Solution is a plastic bottle sprayer or with a plastic pump up garden sprayer. Never use mechanical equipment with metal parts to apply the Patina/Antique Solution, it is corrosive and may ruin the equipment. Misting will achieve the most uniform oxidation on the finish, although there will be highs and lows. A completely uniform finish should not be the expected results. The Patina/Antique Solution can be sprayed, splashed or brushed. Each will achieve different and varying results. It takes 12 to 24 hours before the patina will fully develop.

FOLLOW THESE FIVE SIMPLE STEPS
  1. Clean or wash off all dirt, oils and grease, flaking paint and remove all rust or oxidation.
  2. Prime all non-metal surfaces with our clear primer sealer. Metal surfaces must be primed with a high quality epoxy primer.
  3. Apply the first coat of Metallic Coating to all surface area with brush, roller or sprayer. Allow 24 hours curing time between coats.
  4. Apply second coat of Metallic Coating. Temperatures should be between 40 F & 80 F.
  5. If a Verdigris Patina finish is desired, mist the green patina solution on the second coat of the Metallic Coating while it is still damp to the touch. Use a fine misting bottle sprayer.

YOU’RE DONE, THE PATINA WILL CHANGE TO AN ANTIQUE FINISH WITHIN 30 MINUTES.

We sell Copper and Bronze Coatings in quart and gallon size to be used with the Patina Solution. Also available Clear Acrylic Sealer & Primer.

Available Commercial Patina Finishes

Sample Green Patina With Bronze Coating

Green Patina on Bronze

Sample Green Patina On Copper Metallic Coating

Green Patina on Copper

Sample Green Patina With Iron Coating

Green Patina on Iron

Commercial Use: Clear Acrylic Sealer & Primer

Primer on non-metal surfaces or as a clear sealer

A pure acrylic base with no extenders or color added. Great product for interior and exterior projects. This product can be brushed, rolled or sprayed. For use as a primer on non-metal surfaces or as a clear sealer on hardy backer and concrete both interior and exterior.

Architectural Applications

Interior Design Applications

Talk to Us About Your Customized Project

Questions? Talk to a live person.

We are family owned and family helpful. Our friendly sales staff can help in decision making for any application and can then get the product shipped quickly to you. 

Pricing based on quantity ordered plus FedEx shipping. Call to order.

I wanted something that looked like real copper and this was it. The label says liquid copper and that's exactly what it is. coverage is great, I would buy this product again.

Or email us instead.

Scroll to Top